Chimney Repair in Gilbert, AZ | Chimney Sweep Gilbert

Chimney Repair in Gilbert - Inspected on Camera, Then Priced in Writing

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Gilbert Homeowners

Most chimney problems in Gilbert announce themselves quietly – a hairline crack in the crown, a cap that came loose in a monsoon gust, a flue liner that’s been quietly spalling behind the masonry for years. Chimney repair is the work of catching those problems before they turn into a fire risk or a four-figure rebuild, and it starts with an inspection that shows you what’s actually wrong. We diagnose before we quote, so nothing gets recommended that you can’t see for yourself in a camera photo. Our technicians have up to 14 years of experience, and we work exclusively with trade-grade materials from names like Olympia Chimney, DuraFlex, and Copperfield. Chimney repair in Gilbert is often booked same-day. Call (866) 942-9144 and we’ll get you scheduled. We answer 24/7.

Call (866) 942-9144

Chimney Cap Installation

Chimney Cap Installation is fitting a protective cover over the top of the flue to keep out rain, birds, squirrels, and the debris that plugs a flue over time. You need one when your chimney has no cap at all, or when the existing cover is a thin spark screen that’s rusted through. In Gilbert’s desert setting, an uncapped flue takes in dust, monsoon rain, and nesting material on a regular basis, and a wet flue is a corroded flue. We install caps sized to the actual flue opening, using Famco and Copperfield components that fit to manufacturer spec rather than a generic lid strapped on top. Cap installation typically runs $185 to $450 depending on the flue size, the number of flues, and whether a custom top plate is needed. The written estimate sets the final price.

Single-Flue and Multi-Flue Caps

A single-flue cap protects one opening; a multi-flue cap spans the whole crown and covers every flue under one top plate. We measure each opening separately, because a cap that’s too loose rattles and one that’s too tight won’t sit flat. Getting the fit right is what keeps water from wicking in at the edges.

When a Cap Won’t Fit the Existing Crown

Some crowns are irregular or crumbling at the edges, and a cap needs a sound surface to anchor to. In those cases we’ll tell you plainly that crown work comes first. There’s no point bolting a new cap onto masonry that’s about to fail.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is the removal of a failed, rusted, or storm-damaged cap and the fitting of a new one. You need it when the old cap has rusted through, lost its mesh, or been bent out of shape by wind, and you can usually spot it from the ground as a sagging or missing top. A cap that’s come loose no longer keeps out rain or wildlife, and a missing cap on an active flue is worth addressing before the next storm season. We remove the old unit, check the crown and flue tile underneath for damage the old cap may have been hiding, and fit a replacement sized correctly. Replacement generally falls in the $185 to $450 range, with the exact figure depending on flue count, cap style, and any crown repair needed at the same time. The written estimate is the final word on price.

What the Old Cap Was Hiding

When a cap comes off, the flue tile and crown underneath have usually been exposed for a while. We look at both before fitting the new unit. If the crown is cracked or the tile is spalled, you’ll see it in the photos and we’ll explain what can wait and what can’t.

Matching the Cap to the Flue

A cap that’s too small restricts draft; one that’s oversized lets water blow in under the edges. We size to the flue opening and the appliance type, whether that’s an open wood fireplace or a gas insert. Fit matters more than finish.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 942-9144

Chimney Liner Installation

Chimney Liner Installation is putting a new flue liner inside the chimney to contain heat and combustion gases and to replace a liner that’s cracked, spalled, or missing. You need it when an inspection shows clay tile that’s broken or deteriorated, when there’s no liner at all in an older chimney, or when a new appliance requires a correctly sized flue. This is life-safety work. A compromised liner lets heat and carbon monoxide reach the surrounding structure, so it’s not a job for a generalist. We install DuraFlex flexible liner systems, and for liners that are deteriorated but still structurally sound we can resurface with HeatShield rather than tear out. Liner installation typically runs $2,400 to $5,800 depending on height, flue size, and whether insulation is added. The written estimate sets the final price.

Relining Versus Resurfacing

Not every damaged liner needs full replacement. HeatShield resurfacing can rehabilitate a flue that’s deteriorating but intact, which is a capability most sweep-only outfits don’t have. We’ll tell you which route your flue actually needs, with camera evidence to back it up.

Flexible Liners in Tight Flues

Older masonry chimneys rarely have a straight, uniform flue, and a rigid liner won’t go where a flexible one will. DuraFlex systems handle offsets and irregular tile without cutting corners. The liner is specified to the appliance, not picked off a shelf.

Chimney Flashing Repair

Chimney Flashing Repair is fixing the metal seal where the chimney meets the roof, the joint most likely to leak when it fails. You need it when you see water staining on the ceiling near the chimney, rusted or lifted flashing, or daylight at the seam. Flashing takes the brunt of wind-driven rain, and in Gilbert a monsoon can find a lifted edge fast. We reseat and reseal existing flashing where it’s sound, and replace sections that have rusted through or pulled loose, working the counter-flashing into the masonry properly. Flashing repair typically runs $225 to $650 depending on the roof pitch, the extent of the damage, and whether the flashing needs full replacement. The written estimate sets the final price.

Leaks That Aren’t the Flashing

Not every ceiling stain comes from the flashing joint. A cracked crown or an unsealed flue top can send water down the same path. We check all three before quoting a flashing repair, so you don’t pay for the wrong fix.

Working With the Roof Surface

Flashing has to mate cleanly with the roofing material around it, and the approach differs on tile, shingle, and metal. We work the seal so water sheds away from the joint. A repair that just smears sealant over the seam isn’t a repair.

Chimney Crown Repair

Chimney Crown Repair is fixing the concrete or mortar cap at the very top of the chimney that sheds water away from the flue and masonry below. You need it when the crown is cracked, crumbling, or pulling away from the flue tile, which lets water into the chimney structure. That water shows up later as spalled brick, efflorescence, or a rusted damper, so a small crown crack is worth catching early. We rebuild deteriorated crowns with a proper slope so water runs off, and we can resurface minor cracking rather than tear out a crown that’s mostly sound. Crown repair typically runs $350 to $900 depending on size, access, and whether a full rebuild is needed. The written estimate sets the final price.

Want to talk it through?Free estimate, price agreed before work starts
Call (866) 942-9144

Why the Crown Cracks

Crowns crack from sun exposure, thermal movement, and the simple shrinkage of the original pour over time. A hairline crack lets in more water than most people expect. Left alone, it works its way down into the masonry.

Resurfacing Versus Rebuilding

A crown with minor surface cracking can often be resurfaced; one that’s broken into pieces or separated from the flue needs a rebuild. We’ll show you which situation you’re in. The repair follows the evidence, not a sales target.

Chimney Repair Companies

Chimney Repair Companies vary widely in what they actually do, and picking the wrong one is how homeowners end up paying twice. You need a specialist when you want a full-cycle company – inspection, repair, and relining under one accountable contractor – rather than a handyman with a brush or a sweep service that has to subcontract the structural work. We handle all three lines ourselves, which means the person who inspects your flue is the same outfit that quotes and completes the repair. We use trade-grade materials from Gelco, Olympia Chimney, and DuraFlex rather than hardware-store substitutions. Repair work generally runs $225 to $5,800 depending on scope, from a flashing fix to a full reline. The written estimate sets the final price.

What to Ask Before You Hire

Ask whether the company does its own relining or subcontracts it, and whether the inspection comes with photos you can see. Ask what brands they install. A company that can answer those three plainly is usually the one worth keeping.

Why One Contractor Matters

When inspection, repair, and relining sit with three different outfits, nobody owns the outcome. A single point of contact from the first look to the finished repair keeps the diagnosis and the fix connected. That’s how we’re set up.

Chimney Masonry Repair

Chimney Masonry Repair is fixing the brickwork, mortar joints, and structure of the chimney itself, from tuckpointing to partial rebuilds. You need it when mortar joints are eroded, bricks are spalling or loose, or the chimney is leaning or separating from the house. In Gilbert’s heat, mortar takes a beating over the years, and once joints recede, water gets behind the brick and the damage accelerates. We repoint deteriorated joints, replace spalled brick, and address the source of the water before rebuilding. Masonry repair typically runs $400 to $2,800 depending on the area involved and whether a partial rebuild is required. The written estimate sets the final price. Masonry repair often pairs with chimney repair that addresses the flue and cap at the same time.

Spotting Spalled Brick

Spalled brick has a peeling, flaking face where water froze or salt pushed the surface off. It’s a sign the masonry is taking on water it shouldn’t. Catching it early keeps a repointing job from becoming a rebuild.

Repointing Done Right

Repointing means grinding out the old mortar and packing new mortar into the joint, not smearing it over the surface. The mortar has to match the brick’s hardness. A hard mortar on soft brick accelerates the damage it’s meant to stop.

Need a price for your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 942-9144

Brands We Service

We work with components and systems from the chimney industry’s recognized manufacturers, and that shows in how a repair holds up. Olympia Chimney makes caps and venting components, and we specify their parts when the fit has to be exact to the flue. DuraFlex flexible liner systems are our go-to for relining irregular or offset flues, and we know where those liners take stress over time. Copperfield components cover caps and accessories built to manufacturer spec.

Famco and Gelco round out the roster for caps, dampers, and the hardware that ties a repair together. We also use HeatShield for resurfacing liners that aren’t ready for full replacement. The point of working with these names is that the parts fit and the materials last, whether you have Olympia Chimney or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (866) 942-9144

Signs You Need a Pro Right Now

  • Water stains on the ceiling or chimney breast. A stain near the chimney usually means the flashing, crown, or flue top is letting water in. It won’t fix itself, and the longer it runs, the more masonry it damages.
  • Crumbling mortar or flaking brick. Receding mortar joints and spalled brick faces are the first visible stage of masonry decay. Repointing at this point is far cheaper than a rebuild later.
  • A cracked or separated crown. The crown is the chimney’s rain hat. Once it cracks, water goes straight into the structure below, and a small crack can become a broken crown within a season.
  • White staining on the brick. Efflorescence is a mineral deposit left behind when water moves through masonry and evaporates. It’s a visible sign the chimney is wet inside.
  • A damaged or missing flue liner. Cracks, gaps, or a missing liner let heat and carbon monoxide into the structure. This is the one we’d want to see before the next fire is lit, and we can look at it with a camera.

Our Process, Step by Step

  1. 1
    Book the visit and the inspection. We start with a chimney inspection, done with a camera we run down the flue, so we’re seeing the actual condition rather than guessing from the outside. You get photos of what we find.
  2. 2
    Diagnose before we quote. We go through the footage with you and separate what’s urgent from what can safely wait. Nothing gets added to the quote that the camera didn’t show.
  3. 3
    Write the estimate. You get a written estimate that sets the price, with each repair line itemized by scope and material. There’s no pressure to approve anything on the spot.
  4. 4
    Complete the repair. We do the work with trade-grade materials from the brands we’ve named, sized to your flue and appliance. If something changes once we’re into the job, you hear it from us before extra work begins.
  5. 5
    Verify and walk you through it. We check the repair, and where it applies, run the camera back down the flue to confirm it’s sound. You see the result before we consider the job closed.

How Much Does Chimney Repair Cost in Gilbert?

Chimney repair in Gilbert typically runs from about $185 for a straightforward cap installation up to $5,800 for a full reline, with most structural repairs landing in the $350 to $2,800 range. A typical flashing repair in Gilbert runs $225 to $650 depending on roof pitch and damage extent, while a crown rebuild usually falls between $350 and $900. Masonry repointing scales with the area involved, generally $400 to $2,800.

What affects the price most is scope, not the address. Roof pitch and access add labor on flashing work. Chimney height drives liner cost, and adding insulation to a liner nudges it up. Whether a repair is a patch or a rebuild makes the biggest difference of all, which is why we diagnose with a camera before quoting anything.

How to avoid overpaying: get the written estimate itemized, insist on seeing the camera photos the quote is based on, and ask plainly which repairs can wait. If a company can’t show you why a repair is needed, don’t approve it. A free estimate from us includes the inspection findings, the photo report, and a flat price agreed before we book the work. There’s no charge for the estimate, and you’re under no obligation to go ahead.

Want to talk it through?Free estimate, price agreed before work starts
Call (866) 942-9144

Our Service Area Near Gilbert

We serve Gilbert and the surrounding East Valley, including Mesa, Chandler, and Tempe, plus communities further out like Maricopa, Blackwater, Komatke, Stotonic Village, Lower Santan Village, and Upper Santan Village. Homes in this part of the valley share the same conditions – intense sun on the masonry, monsoon wind and rain on the cap and flashing – so the same failure patterns come up again and again. If you’re outside Gilbert proper, chimney repair in Maricopa is handled by the same team and the same process.

Serving Gilbert, AZ – Our Local Coverage Area

We serve Gilbert and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Gilbert

Schedule Your Chimney Repair Service in Gilbert Today

If you’ve seen a stain, a crack, or a crumbling joint, the next step is a look with a camera, not a guess. Call (866) 942-9144 to book chimney repair in Gilbert. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get a free, no-obligation estimate, a flat price agreed before booking, and camera photos that show exactly why the work is needed. Sweep, repair, inspect – one company, one call. See our full chimney sweep and inspection services, or reach out for chimney repair near Blackwater. Same team, same process.

Written by the team at Chimney Sweep Gilbert.

Why Gilbert Chooses Chimney Sweep Gilbert

We set the standard for chimney repair in Gilbert.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Gilbert

Getting your chimney repair project started is simple.

1

Call or Request a Free Estimate

Tell us about your chimney repair project and we set up a free visit. No obligation and no hidden fees.

2

Licensed Estimator Visits

A licensed, insured estimator inspects and measures on site, then gives you a clear written price.

3

Scheduled and Done Right

Your crew does the work on the date in your quote, backed by our workmanship warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Gilbert Customers Say

Trusted by homeowners across Gilbert and surrounding areas.

★★★★★

"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."

Katie Sutton
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Omar Haddad
★★★★★

"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."

Brooke Bennett

Ready for Chimney Repair in Gilbert?

Call now for a free estimate, or request one below. Licensed, insured, and ready to schedule your free estimate in Gilbert.

(866) 942-9144

Request a Free Estimate in Gilbert

Tell us about your chimney repair needs. We'll get back to you to set up your free estimate.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Local Service Coverage
Call Now - We Answer 24/7